adviceharp91

How to Change a Subaru Spare Key If you've lost your Subaru car key, call a locksmith. Locksmiths usually can cut you a key cheaper than the dealer. Subaru car keys are generally either intelligent “push-to-start” fob remote keys or basic metal keys. The Fob key comes with an embedded chip that must be reprogrammed. Keyless Entry System A key fob lets you to lock or unlock your Subaru from a distance and can also open the trunk or lift gate of your vehicle. These remotes are connected to the keypad in your car to connect with your computer system in your vehicle. Subaru models have a little known feature dubbed PIN Code Access. You can choose a personal number sequence to start and unlock your car. Check your owner's guide to learn how to use this feature if you have a Subaru Forester, Outback Crosstrek, WRX STI or Impreza. It's likely that the battery inside the key fob has failed. You can check the battery life of your key fob with the portable tester or multimeter that you have in your garage. The next step is to take the key fob out of its case, and then examine its transmitter circuit board. It will have one or two sets of 8-digit numbers, so jot down the first set so you can remember it later. Once you've finished, put the key fob back together and you'll be able to begin programming it at home. how to get a new subaru key fob for doing this is different based on the model and year of your vehicle, but it's usually simple enough to complete yourself. Key Fobs Subaru's latest models all feature key fobs that can not only unlock doors, but also turn on your lights, lock the gas cap, and even start your vehicle. This feature is especially useful if been at a gas station and your car won't even start because the battery inside the key fob has gone out. If your Subaru is new or old, it's likely that the key fob is able to be replaced with minimal difficulty. It's important to note that models with high levels of technological sophistication might require an excursion to the dealer. With just a bit of effort and time, you can create your own replacement key fob. Begin by looking at the transmitter circuit board inside your key fob (instructions to open the case must be included in your owner's manual). It should contain two or three serial numbers, each of which is 8 digits long. Write down the initial number series and keep it in your wallet to refer to later on. Then, sit in your driver's seat, and close all doors. Turn the key to start your vehicle, then turn off after ten revolutions. Press the lock button on the key fob and open the door to ensure that all of your doors work correctly. Close the door, then take the key off. You should hear your vehicle buzz again, which indicates that the key fob has been programmed. Ignition System If your Subaru keys aren't functioning as they ought to, it could be because the key battery is dead. You can replace the battery in your key fob on your own if know how. A replacement battery is cheap and relatively easy to locate. If your key fob doesn't respond to your commands, it could be a different issue. It's best to visit a dealership to purchase an extra key. They will make sure that the key is genuine Subaru key, that is in warranty, and that it is programmed to your vehicle. This is much easier and safer than purchasing an aftermarket key from a business online. You can also ask the dealer cut a brand new key if you provide them with your VIN number as well as proof of ownership. They'll use this information to create a code for the replacement key so that it can be accepted by the immobilizer. This process is more involved than cutting a new one, and the dealership will usually charge more for this service. Once the new key is programmed then you'll be able change it over to your existing key. It takes just five seconds to insert the new key, so be sure to keep your working keys close at your side. You can take the key off when the security light has stopped flashing, and then test it. Battery Replacement One of the primary features that make Subaru fobs so useful is their ability to switch on your car's power windows as well as sunroof by pressing of a button. However, the battery inside the Subaru key fob was not intended to last forever, and will eventually require replaced. The good news is that replacing the battery is a straightforward procedure that you can do yourself with the help of this quick guide from Capitol Subaru. To start the process, you'll have to find the tiny crevice inside the seam that divides the back and front of your key fob. It is possible to open this gap using an flat-head screwdriver to expose the small compartment that contains the battery. Install the new battery and ensure it's facing in the correct direction. Remove the old one. After you've put everything together, you can use the new key fob for locking, unlocking, and starting your vehicle. It's always recommended to have an additional set of keys available, especially if you've lost one or not functioning properly. A new key can be purchased at your local auto dealer, or you can have one cut by the locksmith. It is essential that your key fob is working properly as soon you can to ensure that you are able to drive safely.